This article mainly introduces:

Nepal hydraulic cylinder,construction machinery hydraulic cylinder manufacturer,construction machinery hydraulic cylinder

(Nepal construction machinery hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

construction machinery hydraulic cylinder are widely used in Nepal，because of high work efficiency，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed construction machinery hydraulic cylinder for customers from Nepal.

Introduction to construction machinery hydraulic cylinder:

There are some honeycomb holes in the inner wall of the construction machinery hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the construction machinery hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the construction machinery hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the construction machinery hydraulic cylinder is targeted to prevent. Is very necessary.

In use, the construction machinery hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the construction machinery hydraulic cylinder.

If the construction machinery hydraulic cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the construction machinery hydraulic cylinder. The internal parts of the construction machinery hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the construction machinery hydraulic cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the construction machinery hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the construction machinery hydraulic cylinder bore processing is out of whack. Because the piston and construction machinery hydraulic cylinder, guide rail and piston rod are relative If the construction machinery hydraulic cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling construction machinery hydraulic cylinder weight composition and calculation. The weight of the construction machinery hydraulic cylinder is composed of the construction machinery hydraulic cylinder diameter, the outer diameter and weight of the construction machinery hydraulic cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

When the construction machinery hydraulic cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

Answers to some questions about construction machinery hydraulic cylinder:

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.

Can multiple identical hydraulic cylinders be supplied with the same supply line?
This can be connected, but there is a disadvantage, that is, the hydraulic cylinder with the minimum pressure is extended first, and then the pressure is higher, and then the higher, until all the hydraulic cylinders are extended, which may not meet the requirements of field use.